Ducati Shock Spanner Tool

This is a shock spanner that fits all Ohlins and Showa shocks. This
tool is designed to precisely fit the locking rings and the slim design
allows it to get into tight spaces so that preload can easily be
adjusted. It is CNC machined out of high grade steel and then clear
zinc plated so it will last forever.  We suggest you buy two to lock the
rings together.
Anti-Marr Fork Cap Wrench

These are a non-marring fork cap wrench that fits your bikes  forks.
These wrenchs will allow you to remove your fork caps without
worrying about damaging them. The wrench has an aluminum
handle and a delrin insert to protect the nut from damage.  They are
available in three sizes:  30mm (Blue), 32mm (Red), and 35mm (Black).
Sizes
30mm (Blue) Fits:
Marzocchi forks on Ducati Monsters
and SS/CR models
Any other bike with 30mm fork caps.

32mm (Red) Fits:
1098/1198/SF
748/916/996/998
MONSTERS
SUPERSPORTS
HYPERMOTARD
Any other bike with 32mm fork caps.

35mm (Black) Fits:
Any bike with 35mm fork caps.
Ducati front axle drift 25mm

This is front axle drift for all Ducati's with a 25mm I.D. axle.  This tool
allows you to safely remove a stubborn axle. The side that fits inside
the axle is made out of aluminum so it will not harm your axle. The
other side has a stainless steel end cap so that when you tap it with a
hammer it will not mushroom.

This tool fits:  749/999, 748 916/996/998, ST2/ST3/ST4, Monster,
Multistrada, Hypermotard, Sport classic, Supersport, And many more
Ducati Alternator cover puller fits all modern Ducati's

This tool is used to remove the alternator cover. It allows you to do
this without prying on it with a screw driver. This is a must have tool
for anybody putting a lightweight flywheel in their bike, if you fry your
alternator wires or if you plan on removing the cover for a general
inspection. It fits all modern Ducati motorcycles. The part is CNC
machined out of billet 6061 aluminium and is clear chromate plated to
provide many years of corrosion free use.
Chain adjusting tool for Ducati

This is a Ducati chain adjuster tool for the Ducati single sided
swingarm bikes  This tool is CNC machined out of billet aluminum.  
These are model specific.
Select Model
Ducati tool package *3PC set*

This is a 3 piece tool kit for your Ducati.  It includes a wheel nut
socket, front axle alignment tool, and a chain adjuster.
Select Model
Fork type
OHLINS 50mm fork cap wrench 748 996 998 916

This item is a fork cap wrench for 50mm ohlins forks. These forks
came stock on many Ducati 748,916,996,998. The top of your forks
should measure 50mm or just under 2". This tool is specifically
designed to remove the fork cap without damage.  It is CNC
machined out of billet aluminum with hardened dowel pins. It comes
with a clear chromate plating
Ducati steering stem nut tool

This tool fits almost every Ducati motorcycle 1992 or newer.  This
tool is the only way to remove the nut when you are greasing the
stem bearings. It is also good to periodically make sure it is tourqed
down tight. The tool has a square hole on the backside for a 3/8"
drive rachet. It is equivalant to Ducati tool # 88713.1058. This tool is
machined out of 6061 billet aluminium and then anodized.
Ducati front axle alignment tool

This is a front axle alignment tool.  This tool keeps the notch in the
axle properly lined up with the notch on the fork bottom when
tightening the front axle nut. This alignment has to be correct so that
there is access to the commpression adjustment screw. This is a
high quality tool made out of 6061 aluminum and then clear chromate
plated to provide many years of corrosion free use.  It is available in
three sizes:  25mm (most Ducs with Showa), 25mm Ohlins Specific,
1098S/R, 1198S/R, and One for the Hypermotard.
Model
Ducati Cam holding tools

This tool holds intake cam wheel in place during cam belt installation.
The teeth on this tool lock the vertical (rear) cylinder intake cam from
rotating so that you can remove the old belt and install the new one.
This is a must have tool if you are replacing your worn out belts. It is
CNC machined out of 6061 billet aluminum and then clear chromate
plated to resist corrosion.   There are two Different versions, One for
the 748 916 996 851 888 motors and one for the 749 999 998
testrastretta motors
Type
Ducati ride height tool for the 748/916/996/998

The secret to proper suspension set up on a Ducati 748-998 starts
with the proper ride height. This tool allows you to measure it by
giving you a standardized marked reference point. Every time you
adjust your chain the ride height changes because of the eccentric in
the swingarm. The plug that goes into the rear axle comes with a
stainless thumb screw to attach it to the tool for storage. This tool is
CNC machined out of billet aluminum and comes in two colors black
or gold.
Color
Ducati 55mm/30mm wheel nut socket

Wheel nut tool for your Ducati 1098/1198, Multi 1200, Diavel, or
Streetfighter. It is two tools in one a, 55mm 12pt for the rear and a
30mm for the front. The tool is made out of billet aluminum so that it
is light weight and can be carried in a tool kit. It is then hard
anodized. This makes it about 3 times harder than your standard
colored anodize coating. It is designed to be used with a 1/2" ratchet.
This is a must have tool because the Honda/Yamaha superstore will
not have a socket to change your rear tire. All of our tools come with
a 100% satisfaction guarantee.
OHLINS 50mm fork cap wrench for 1198/ 1098/
Streetfighter

Ths is a fork cap wrench for a Ducati 1098S/1198S/Streetfighter with
Ohlins forks. The top of your forks should measure 52.7mm or
2.075". This tool is specifically designed to remove the fork cap
without damage. Don't let fork maintenance get overlooked because
you don't have the correct tool. It is CNC machined out of billet
aluminum with hardened dowel pins. It comes with a clear chromate
plating to provide many years of corrosion free use.
Hypermotard "S" fork cap wrench

This is a fork cap wrench for all Ducati Hypermotard "S" with
Marzocchi forks. This is the only sensible way to remove the fork
caps without damage. Don't let fork maintenance get over looked
because you do not have the correct tool. This tool is CNC machined
out of billet aluminum and clear chromate plated. All of our products
are made in the USA and come with a 100% satisfaction guarantee.
Crankshaft Turning Tool

This is a Ducati engine turning tool or crank shaft turning tool. It
allows you to safetly rotate the engine while checking the valve
clearances or setting the timing. This tool fits all Ducati's from
1990-2011

This tool has been CNC machined out of high grade steel and then
nickel plated to prevent corrosion.

Includes stainless steel hardware
Ducati Oil Filter Tool

This is a oil filter tool that fits all Ducati's that have a 8 flat oil filter.
This means that it fits all Ducati's from 1991 to the present including
the 1098/1198 and Diavel. It makes the job of removing the stubborn
old filter a breeze. It has a 3/8" square drive so it can be used with a
ratchet. This tool is CNC machined out of billet aluminum in the USA
and comes with a 100% satisfaction guarantee.

Does NOT include oil Filter!
Ducati 28mm Front Axle Nut Socket

This is a Ducati front wheel nut tool. It is designed to fit the thin front
axle nuts on most modern Ducati's. Because the front axle nut is so
thin it can easily be stripped with a sloppy fitting standard socket.
This tool is not a sloppy fit and because it has a raised center it will
not slip off the nut. This tool fits the following models:
748, 916, 998, 996, Hypermotard, Multistrada, All Monsters,
Supersports, Sport Classic, and Any Ducati with a 25mm front axle

This tool has been CNC machined out of billet aluminum and hard
coat anodized.
Because of this tools design it will not strip your front axle nut.
Ducati 41mm/46mm wheel nut socket

This is a Ducati 46mm/41mm wheel nut tool. It is two tools in 1, 46mm
for the wheel side nut and 41mm for the sprocket side nut. This tool
fits the following models:  748, 916,  998, 996, 848, Hypermotard,
Multistrada, Monster 1100, S2R, and the S4R
This tool has been CNC machined out of billet aluminum and then
hard anodized.
Ducati 41mm/46mm STEEL wheel nut socket

This is a Ducati 46mm/41mm wheel nut tool. It is two tools in 1, 46mm
for the wheel side nut and 41mm for the sprocket side nut. This tool
fits the following models:  748, 916,  998, 996, 848, Hypermotard,
Multistrada, Monster 1100, S2R, and the S4R
This tool has been CNC machined out of high grade steel and then
black oxide coated.
Ducati 55mm/30mm STEEL wheel nut socket

Wheel nut tool for your Ducati 1098/1198, Multi 1200, Diavel, or
Streetfighter. It is two tools in one a, 55mm 12pt for the rear and a
30mm for the front. This tool is CNC machined out of high grade steel
and then nickel plated so it will never rust or corrode. It is designed
to be used with a 1/2" ratchet. This is a must have tool because the
Honda/Yamaha superstore will not have a socket to change your rear
tire. All of our tools come with a 100% satisfaction guarantee.
Ducati Clutch Basket Holding Tool

This is a Ducati clutch basket/drum holding tool. This tool is used to
hold the clutch drum in place so you can remove the nut holding it
on. Once the nut is removed you can install a light weight basket or a
slipper clutch. It is also good to periodically make sure the nut is
torqued to spec. This tool does not have a handle to wrestle with, it
mounts to two of the holes for the clutch cover with the stainless
steel hardware that is included. The mounting holes are slotted so
that it is easier to install on the basket and drum. It fits all modern six
speed Ducatis that have a twelve tab dry clutch. It is CNC machined
out of billet 6061 aluminum and clear chromate plated to provide
years of corrosion free use. Made in the USA and comes with a 100%
satisfaction guarantee. It is priced at a fraction of the factory tool!!!
.
News                          Photo Gallery                          Contact Us                          About Us & Other Info                          Dealers
..
Catalog:
Counter